Delta-mannitol to enable continuous twin-screw granulation of a highly dosed, poorly compactable formulation

23 Jul 2024 | Contributor(s): Vanhoorne, V., Almey, R., De Beer, T., Vervaet, C.

In current study, it was investigated if the moisture-mediated polymorphic transition from δ- to β-mannitol during twin screw granulation (TSG) also took place in high drug loaded formulations and if the specific granule morphology associated with the polymorphic transition could enable tableting...

Control oriented modeling of twin-screw granulation in the ConsiGmaTM-25 production plant

09 Jul 2024 | Peer-reviewed journal | Contributor(s): Johannes Khinast, Martin Horn, Jakob Rehrl, Selma Celikovic, Johannes Poms

ConsiGmaTM-25 is a continuous production plant integrating a twin-screw granulation, fluid bed drying, granule conditioning, and a tableting unit. The particle size distribution (PSD), active pharmaceutical ingredient (API) content, and liquid content of wet granules after twin-screw...

Visualization and understanding of the granulation liquid mixing and distribution during continuous twin screw granulation using NIR chemical imaging

09 Jun 2023 | Peer-reviewed journal | Contributor(s): Vercruysse, Jurgen, Toiviainen, Maunu, Fonteyne, Margot, Helkimo, Niko, Ketolainen, Jarkko, Juuti, Mikko, Delaet, Urbain, Van Assche, Ivo, Remon, Jean Paul, Vervaet, Chris, De Beer, Thomas

Over the last decade, there has been increased interest in the application of twin screw granulation as a continuous wet granulation technique for pharmaceutical drug formulations. However, the mixing of granulation liquid and powder material during the short residence time inside the screw...

Using online mass spectrometry to predict the end point during drying of pharmaceutical products

09 Jun 2023 | Peer-reviewed journal | Contributor(s): Dodda, Aditya G., Saranteas, Kostas, Henson, Michael A.

Drying of active pharmaceutical ingredients (APIs) is an energy-intensive process that is often a manufacturing bottleneck due to the relatively long processing times. A key objective is the ability to determine the drying end point, the time at which all solvent has been evaporated from the...

Using residence time distribution in pharmaceutical solid dose manufacturing–A critical review

09 Jun 2023 | Peer-reviewed journal | Contributor(s): Bhalode, Pooja, Tian, Huayu Gupta, Shashwat Razavi, Sonia M Roman-Ospino, Andres Talebian, Shahrzad Singh, Ravendra Scicolone, James V Muzzio, Fernando J, Ierapetritou, Marianthi

While continuous manufacturing (CM) of pharmaceutical solid-based drug products has been shown to be advantageous for improving the product quality and process efficiency in alignment with FDA’s support of the quality-by-design paradigm (Lee, 2015; Ierapetritou et al., 2016; Plumb, 2005; Schaber,...

Use of the channel fill level in defining a design space for twin screw wet granulation

09 Jun 2023 | Peer-reviewed journal | Contributor(s): Gorringe, L. J., Kee, G. S., Saleh, M. F., Fa, N. H., Elkes, R. G.

Twin screw wet granulation is a key process in the continuous manufacture of oral solid dosage forms. Previous Research Article has qualitatively suggested that the channel fill level influences the granules produced. In this paper a quantitative measure of the total volumetric fraction of the...

Understanding API Static Drying with Hot Gas Flow: Design and Test of a Drying Rig Prototype and Drying Modeling Development

09 Jun 2023 | Peer-reviewed journal | Contributor(s): Ottoboni, S, Coleman, SJSteven, C, Siddique, M, Fraissinet, M, Joannes, M, Laux, A, Barton, A, Firth, P, Price, CJ, Mulheran, PA

Developing a continuous isolation process to produce a pure, dry, free-flowing active pharmaceutical ingredient (API) is the final barrier to the implementation of continuous end-to-end pharmaceutical manufacturing. Recent work has led to the development of continuous filtration and washing...

TPLS as predictive platform for twin-screw wet granulation process and formulation development

09 Jun 2023 | Peer-reviewed journal | Contributor(s): Ryckaert, A., Van Hauwermeiren, D., Dhondt, J., De Man, A., Funke, A., Djuric, D., Vervaet, C., Nopens, I., De Beer, T.

In recent years, the interest in continuous manufacturing techniques, such as twin-screw wet granulation, has increased. However, the understanding of the influence of the combination of raw material properties and process settings upon the granule quality attributes is still limited. In this...

Transfer from High-Shear Batch to Continuous Twin Screw Wet Granulation: A Case Study in Understanding the Relationship Between Process Parameters and Product Quality Attributes

09 Jun 2023 | Peer-reviewed journal | Contributor(s): Beer, Paul, Wilson, David, Huang, Zhenyu, De Matas, Marcel

A twin screw to high-shear batch granulation technology switch was evaluated for a pharmaceutical development project. Differences in granule (particle size distribution and porosity) and tablet (dissolution) quality attributes were analysed for both continuous and batch technologies. Liquid to...

Twin screw granulation - review of current progress

09 Jun 2023 | Peer-reviewed journal | Contributor(s): Thompson, M. R.

Twin screw granulation (TSG) is a new process of interest to the pharmaceutical community that can continuously wet granulate powders, doing so at lower liquid concentrations and with better product consistency than found by a high shear batch mixer. A considerable body of Research Article has...

Thin-Film Evaporator Model for Continuous Active Pharmaceutical Ingredient Manufacturing

09 Jun 2023 | Peer-reviewed journal | Contributor(s): Lee, BW, Yin, KHSplaine, K, Roesch, B

Thin-film evaporator (TFE) is a popular continuous distillation/evaporation technology for pharmaceutical and fine chemical industries and has several equipment and process configurations that make fundamental modeling approaches very challenging. Specifically, moving wipers and lack of fluid...

The scope of PAT in real-time advanced control of tablet quality

09 Jun 2023 | Peer-reviewed journal | Contributor(s): Singh, Ravendra, Ierapetritou, Marianthi, Ramachandran, Rohit

Continuous pharmaceutical manufacturing together with process analytical technology (PAT) provides a suitable platform for automatic feed-forward/feed-back (FF/FB) control of the end product quality as desired by quality by design (QbD)-based efficient manufacturing. The precise control of the...

The Influence of Equipment Design and Process Parameters on Granule Breakage in a Semi-Continuous Fluid Bed Dryer after Continuous Twin-Screw Wet Granulation

09 Jun 2023 | Peer-reviewed journal | Contributor(s): Ryckaert, Alexander, Ghijs, Michael, Portier, Christoph, Djuric, Dejan, Funke, Adrian, Vervaet, Chris, De Beer, Thomas

The drying unit of a continuous from-powder-to-tablet manufacturing line based on twin-screw granulation (TSG) is a crucial intermediate process step to achieve the desired tablet quality. Understanding the size reduction of pharmaceutical granules before, during, and after the fluid bed drying...

The effect of screw configuration and formulation variables on liquid requirements and granule quality in a continuous twin screw wet granulation process

09 Jun 2023 | Peer-reviewed journal | Contributor(s): Vandevivere, L., Van Wijmeersch, E., Hausler, O., De Beer, T., Vervaet, C., Vanhoorne, V.

The effect of two screw configurations with varying stagger angle was evaluated on the liquid amount required to produce good quality granules for a highly (mannitol-based) and a poorly (DCP-based) soluble formulation containing different binders. It is generally known that the use of a higher...

The impact of channel fill level on internal forces during continuous twin screw wet granulation

09 Jun 2023 | Peer-reviewed journal | Contributor(s): Torrecillas, Carlota Mendez, Gorringe, Lee J., Rajoub, Nazer, Robertson, John, Elkes, Richard G., Lamprou, Dimitrios A., Halbert, Gavin W

The forces experienced by the particles inside a twin screw granulator (TSG) are one of the most difficult parameters to measure quantitatively. However, it is possible to perform accurately this measurement through the use of dye containing calibrated microencapsulated sensors (LAMES) whose...

Technoeconomic Optimization of Continuous Crystallization for Three Active Pharmaceutical Ingredients: Cyclosporine, Paracetamol, and Aliskiren

09 Jun 2023 | Peer-reviewed journal | Contributor(s): Diab, S, Gerogiorgis, DI

Mixed suspension, mixed product removal (MSMPR) crystallizers are widely implemented for the continuous crystallization of active pharmaceutical ingredients (APIs), allowing enhanced efficiency, flexibility, and product quality compared to currently dominant batch crystallizer designs....

Technoeconomic Optimization of a Conceptual Flowsheet for Continuous Separation of an Analgaesic Active Pharmaceutical Ingredient (API)

09 Jun 2023 | Peer-reviewed journal | Contributor(s): Jolliffe, HG, Gerogiorgis, DI

Continuous Pharmaceutical Manufacturing (CPM) has recently emerged as a promising alternative to current batch production methods, which require significant expenditures in order to ensure product quality and process reliability. Advances in new continuous synthesis routes, demonstrations of full...

Systematic Framework for Design and Adaption of Fast, Flexible, Continuous Modular Plants

09 Jun 2023 | Workshop | Contributor(s): Singh, Ravendra, Gernaey, Krist Gani, Rafiqul, Woodley, John

Not available

Systematic framework for implementation of material traceability into continuous pharmaceutical tablet manufacturing process

09 Jun 2023 | Peer-reviewed journal | Contributor(s): Billups, Matthew, Singh, Ravendra

Purpose: With the applications of more advanced manufacturing technologies being applied to the pharmaceutical industry, continuous processes are at the forefront of innovation. One area that is highly desired to be systematically investigated is material traceability in continuous manufacturing...

Systematic substrate adoption methodology (SAM) for future flexible, generic pharmaceutical production processes

09 Jun 2023 | Peer-reviewed journal | Contributor(s): Singh, Ravendra, Godfrey, Andy Gregertsen, Björn Muller, Frans Gernaey, Krist V Gani, Rafiqul, Woodley, John M

The discovery of an effective and safe pharmaceutical product is based on success in clinical trials. Often, several candidate compounds targeting the same disease area are tested in order to identify the most efficacious products. This involves the manufacture of small quantities of compounds...

System-wide hybrid MPC–PID control of a continuous pharmaceutical tablet manufacturing process via direct compaction

09 Jun 2023 | Peer-reviewed journal | Contributor(s): Singh, Ravendra, Ierapetritou, Marianthi, Ramachandran, Rohit

The next generation of QbD based pharmaceutical products will be manufactured through continuous processing. This will allow the integration of online/inline monitoring tools, coupled with an efficient advanced model-based feedback control systems, to achieve precise control of process variables,...

Systematic computer-aided method and tool (ICAS-PAT) for design, analysis &/or validation of process monitoring and analysis systems (PAT systems)

09 Jun 2023 | Workshop | Contributor(s): Singh, Ravendra, Gernaey, Krist, Gani, Rafiqul

Not available

Surrogate-based Optimization for Pharmaceutical Manufacturing Processes

09 Jun 2023 | Peer-reviewed journal | Contributor(s): Wang, Zilong, Escotet-Espinoza, M Sebastian Singh, Ravendra, Ierapetritou, Marianthi

The development of pharmaceutical manufacturing processes has been facilitated by recent advances in the process simulation area. However, since the simulations are usually complex and the analytical expressions of the model can be unknown, it is difficult to directly apply traditional...

Switching from batch to continuous granulation: A case study of metoprolol succinate ER tablets

09 Jun 2023 | Peer-reviewed journal | Contributor(s): Kotamarthy, Lalith, Feng, Xin, Alayoubi, Alaadin, Bolla, Pradeep Kumar, Ramachandran, Rohit, Ashraf, Muhammad, O'Connor, Thomas, Zidan, Ahmed

Continuous manufacturing (CM) has been used to produce several immediate release drug products. No extended-release (ER) product manufactured employing CM technology has been approved yet. This study investigated the critical aspects of switching from the batch mode of high shear granulation to...

Simulation-Based Design of an Efficient Control System for the Continuous Purification and Processing of Active Pharmaceutical Ingredients

09 Jun 2023 | Peer-reviewed journal | Contributor(s): Sen, M, Singh, R, Ramachandran, R

In this study, an efficient system-wide controlsystem has been designed for the integrated continuous purification and processing of the active pharmaceutical ingredient (API). The control strategy is based on the regulatory PID controller which is most widely used in the manufacturing industry...